//==========================================================================//
//   Flowsquare+ parameter file...              -- 2020R1.1 --                //
//--------------------------------------------------------------------------//
//   You may directly edit this file, but follow below rules. Each          //
//   parameter entry consists of three blocks divided by [SPACE] or         //
//   double-slash(//). The order of these entries can be arbitorary.        //
//   Example:                                                               //
//   003:name     0.00123456789   // some explanation of the parameter      //
//   ^^^^^^^^^    ^^^^^^^^^^^^^     ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^     //
//   1st block      2nd block          3rd block starts after (//).         //
//==========================================================================//
----- General Parameters ----------------------------------------------------------------------------------

002:cmode                                   1  // Simulation mode. [0] Fluid simulation mode (constant density and temperature, suitable for gas and liquid single-phase flows). [1] Thermo-fluid simulation mode (variable density and temperature, suitable for gas phase flows).
003:parallel                                2  // Level of parallelism. [0] Serial (no parallelism). [1] Two, parallelism=2. [2] Low, max(2, maxThreadsAvail/4). [3] Medium, max(2, maxThreadsAvail/2). [4] High, max(2, maxThreadsAvail).
004:domx                                 1400  // Nominal screen size (horizontal) during simulations. (unit: pixels)
005:nx                                    300  // Number of mesh points in x-direction. This number may be set independent from physical domain dimensions.
006:ny                                    180  // Number of mesh points in y-direction. This number may be set independent from physical domain dimensions.
007:lx                                    3.5  // Physical domain size in x-direction. (unit: m)
008:ly                                    2.1  // Physical domain size in y-direction. (unit: m)
009:sts                                     0  // Start time step. A new simulation starts from sts=0. To restart, sts should be a timestep at which dump data was output in the previous simulation.
010:latts                               20000  // End time step. For simulations under a trial license, this is limitted.
011:nfig                                 1000  // Interval time step for image output. Result images are saved in the 'image' directory once in every 'nfig' time steps. Setting zero value disable image output.
012:nfile                                1000  // Interval time step for dump data output. Result dump data are saved in the 'dump' directory once in every 'nfile' time steps. Setting zero value disable dump output.
----- Boundary and Initial Conditions --------------------------------------------------------------------

014:presW                             1.0E+05  // Mean pressure. Atmospheric pressure is 1.013E+5 (Pa). (unit: Pa)
015:tempW                               300.0  // Temperature of the initial field (WHITE color). (unit: K, Kelvin) T (K) = 273 + T (deg.C). For example, a room temperature of 20 (deg.C) is 293 (K). [*] This parameter is effective for 'cmode=1'. 
016:vinB                                  1.0  // Y-velocity component for the BLUE inflow boundry. If the value is set as '-', this boundary is slip boundary in y-direction. (unit: m/s)
017:tempB                                   -  // Temperature for the BLUE inflow boundry. If zero value is set, the boundary is treated as adiabatic. If the value is set as '-', no temperature constraint is imposed on this boundary. (unit: K) [*] This parameter is effective for 'cmode=1'. 
018:tempR                               350.0  // Temperature for the RED inflow boundry. If zero value is set, the boundary is treated as adiabatic. If the value is set as '-', no temperature constraint is imposed on this boundary. (unit: K) [*] This parameter is effective for 'cmode=1'. 
019:tempWallK                               0  // Temperature for the wall boundry specified with preset BLACK color. If zero value is set, the boundary is treated as adiabatic. (unit: K) [*] This parameter is effective for 'cmode=1'. 
----- Physical and Model Parameters ------------------------------------------------------------------------

021:mu                                 1.8E-5  // Dynamic viscosity of the fluid. mu is approximately 1.8E-5 (kg/m/s) for the atmospheric air at 15~25 (deg.C). For water at 20 (deg.C), mu is 1.0E-3 (kg/m/s). (unit: kg/m/s)
022:gfy                                  -9.8  // Body force in y-direction. Gravitational force is approximately -9.8 m/s^2. (unit: m/s^2)
----- Graphics & Visualization Parameters ------------------------------------------------------------------

024:ndiv                                    4  // Interval mesh points between displayed visualization related objects such as vectors, streamlines and particles.
#End of file